Calcist

Style

Buttons

Spacing

How much to show

Decimal places

Text size

Water heater size calculator

Count your busiest hour's hot water use to get the first-hour rating to look for, or add up the flow and temperature rise for a tankless heater.

How many of each happen in your busiest hour?

Private: calculated on your device. Nothing you type is sent anywhere.

Next: Going electric? Check the circuit with the electrical load calculator, and the running cost with the electricity cost calculator.

Sizing a tank: first-hour rating

The U.S. Department of Energy says to size a storage water heater by its first-hour rating (FHR): how many gallons of hot water it can supply in an hour, starting with a full tank. It's on the EnergyGuide label. Pick a model whose FHR at least matches your peak-hour demand.

Peak-hour demand = Σ (gallons per use × uses in your busiest hour)
UseGallons per use (DOE worksheet)
Shower20
Shaving (0.05 gal per minute)2
Hand dishwashing or food prep (2 gal per minute)4 (see note)
Automatic dishwasher7
Clothes washer, top-loader25
Clothes washer, front-loader (H-axis)15

Note: DOE's current worksheet lists 3 gallons for hand dishwashing, but its own example (3 showers, 1 shave and 1 hand dishwashing) totals 66 gallons, which counts 4. This calculator uses 4 so it matches that total; the difference is 1 gallon.

Worked example (tank)

DOE's example household has 3 showers, 1 shave and 1 hand dishwashing in its busiest hour: 3 × 20 + 2 + 4 = 66 gallons. It needs a water heater with a first-hour rating of 66 gallons or more. Tank size alone isn't the FHR, so compare the rating on the label, not just the gallons.

Sizing a tankless heater: flow and temperature rise

Tankless (demand) water heaters are rated by the temperature rise they can deliver at a given flow rate. Add up the flow of everything that might run at once, then work out the rise:

Flow (GPM) = Σ fixture flow rates
Temperature rise = wanted temperature − incoming water temperature
Heat output ≈ GPM × rise × 500 BTU/h (8.33 lb per gallon × 60 minutes)
kW = BTU/h ÷ 3,412

Worked example (tankless)

DOE's example: a 0.75 GPM faucet and a 2.5 GPM shower head at once is 3.25 GPM. With 50 °F incoming water and 120 °F wanted, the rise is 70 °F. The heat needed is about 3.25 × 70 × 500 = 113,750 BTU/h of output, or 113,750 ÷ 3,412 = 33.3 kW. (The calculator uses the more exact 8.33 lb per gallon × 60 = 499.8 in place of 500, which gives 113,705, shown rounded as about 113,700 BTU/h.) Look for a model rated for a 70 °F rise at 3.25 GPM or more. DOE notes that gas models are typically rated for a 70 °F rise at about 5 GPM, and electric models at about 2 GPM.

Limitations

  • Groundwater temperature varies by region and season. If you don't know yours, DOE suggests assuming 50 °F; in northern winters it can be colder, so a tankless heater delivers less flow.
  • Low-flow fixtures help. Efficient shower heads and washers lower both peak-hour demand and the GPM needed.
  • Hotter isn't always better. Dishwashers without a booster may want 140 °F (a 90 °F rise), but higher temperatures raise the risk of scalding.
  • Fuel and venting matter as much as size: gas line size, venting and electrical capacity can limit which models fit.

Sources

How we checked this

Before every update, this calculator is run in a real browser with these known answers, and it must match all of them:

  • DOE example, 3 showers + 1 shave + 1 hand dishwashing: 66 gallons ✓
  • 2 showers and a top-loading washer in the same hour: 40 + 25 = 65 gallons ✓
  • Tankless, DOE example: 2.5 + 0.75 GPM = 3.25 GPM at a 70 °F rise ✓
  • Same: about 113,700 BTU/h (33.3 kW) of heating output ✓
  • Edge: inlet water hotter than the target is refused ✓

Last checked October 26, 2026. Spotted something wrong? The math is done in your browser with the formula shown on this page, so you can check any result by hand.

Add this calculator to your website (free)

Paste this code into any web page. The calculator works on your page, resizes itself, has no ads and no tracking cookies, and nothing your visitors type is sent anywhere. More about embedding.

Questions people ask

What size water heater do I need for a family of 4?

Count your busiest hour. If that's 3 showers, a shave and some dishwashing, it's 66 gallons by DOE's worksheet, so look for a first-hour rating of at least 66 gallons.

What is a first-hour rating?

The number of gallons of hot water a tank heater can deliver in one hour starting full. It's on the EnergyGuide label and is the best way to compare tank heaters.

What GPM tankless water heater do I need?

Add the flow of everything that may run at once. One 2.5 GPM shower and a 0.75 GPM faucet need 3.25 GPM at your temperature rise; two showers need 5 GPM or more.

How do I find the temperature rise?

Subtract the incoming water temperature from the temperature you want. 120 °F wanted with 50 °F incoming is a 70 °F rise.

Is a bigger tank always better?

No. A tank much bigger than you need keeps extra water hot all day, which can waste energy through standby heat loss.

Related calculators