Calcist

Style

Buttons

Spacing

How much to show

Decimal places

Text size

Crown molding calculator

Enter your wall lengths to get the linear feet and pieces of crown, and the miter and bevel angles for cutting it flat on a compound miter saw.

Private: calculated on your device. Nothing you type is sent anywhere.

Next: Trimming the floor line too? Use the baseboard calculator.

How crown molding is measured

Crown runs along the top of every wall, where the wall meets the ceiling, so doorways usually don't interrupt it. Measure each wall at the ceiling, not the floor.

Linear feet = sum of the wall lengths − openings
With waste = linear feet × (1 + waste % ÷ 100)
Pieces = linear feet with waste ÷ piece length, rounded up
Pieces if every wall is cut from its own stock = Σ (wall length ÷ piece length, rounded up)

Metrie, a moulding maker, suggests buying about 10% extra for bad cuts and damage. The calculator gives two piece counts: by total footage, and wall by wall (each wall cut from its own pieces, so there are no joints on walls up to the piece length).

Miter and bevel angles (cutting flat)

Cut lying flat on a compound miter saw, crown needs both a miter and a bevel. They depend on the crown's spring angle (how far it leans out from the wall: 38° for common 52/38 crown, 45° for 45/45 crown) and the wall corner angle.

Miter = arctan(sin(spring) ÷ tan(corner ÷ 2))
Bevel = arcsin(cos(spring) × cos(corner ÷ 2))
CrownCornerMiterBevel
38° spring (52/38)90°31.62°33.86°
45° spring (45/45)90°35.26°30.00°
38° spring (52/38)135°14.31°17.55°
45° spring (45/45)135°16.32°15.70°

The 90° values agree with WOODWEB's crown moulding chart (31.61° and 33.86° for 52/38; 35.26° and 30.00° for 45/45) to within rounding. Your saw's manual shows which way to tilt and swing for inside and outside corners.

Worked example

A 12 × 14 ft room: 12 + 14 + 12 + 14 = 52 linear feet of crown. With 10%: 57.2 ft. In 12 ft pieces: 57.2 ÷ 12 = 4.77, so 5 pieces by footage, or 1 + 2 + 1 + 2 = 6 if each wall is cut from its own pieces. For 52/38 crown at the square corners, set the saw to a 31.62° miter and a 33.86° bevel.

Measuring the spring angle

The spring angle is the angle between the back of the crown and the wall once it's installed. It's often printed on the label (52/38 means 38° spring, 45/45 means 45°). If it isn't, hold a short offcut in a framing square the way it sits on the wall and ceiling: one flat on the back against each leg. Then measure the angle between the wall leg and the back of the crown with a bevel gauge and a protractor, or an angle finder. Enter the miter and bevel for that spring angle; the wrong spring angle is the most common reason flat-cut corners don't close.

Coping or mitering inside corners

A mitered inside corner needs two perfect cuts and a perfectly square corner. Walls and ceilings rarely are, so the joint opens. Most trim carpenters cope inside corners instead: the first piece runs square into the corner, and the second is cut with an inside miter to expose its profile, then back-cut along that profile line with a coping saw so it fits over the face of the first piece. A cope forgives a corner that's a couple of degrees off. Outside corners are still mitered, using the angles above.

Cutting nested: upside down and backwards

You don't need a compound bevel at all if you cut crown nested. Stand the crown on the saw at its spring angle, leaning against the fence, upside down: the edge that goes against the ceiling sits on the saw table, and the edge that goes against the wall sits against the fence. Think of the table as the ceiling and the fence as the wall. Then swing the miter to 45° for a 90° corner, with no bevel. Because the crown is upside down, the sides also swap: for an inside corner, the piece for the left-hand wall is the part kept on the right of the blade, and the reverse for the right-hand wall. That's the "backwards" in the saying "upside down and backwards." A stop block clamped to the table keeps the crown at the same angle for every cut.

Tips

  • Walls are rarely exactly 90°. Measure the corner with an angle finder and enter the real angle.
  • Test on scraps first and keep the same orientation for every cut.
  • Long walls: join pieces with a scarf joint (opposing 45° cuts), also cut nested.

Sources

How we checked this

Before every update, this calculator is run in a real browser with these known answers, and it must match all of them:

  • Walls 12, 14, 12, 14 with 10%: 57.2 ft, 5 pieces of 12 ft ✓
  • 52/38 crown at 90°: miter 31.62° ✓
  • 52/38 crown at 90°: bevel 33.86° ✓
  • 45/45 crown at 90°: miter 35.26°, bevel 30.00° ✓
  • 52/38 crown at a 135° corner: miter 14.31° ✓
  • Edge: a 180° corner is refused ✓

Last checked October 26, 2026. Spotted something wrong? The math is done in your browser with the formula shown on this page, so you can check any result by hand.

Add this calculator to your website (free)

Paste this code into any web page. The calculator works on your page, resizes itself, has no ads and no tracking cookies, and nothing your visitors type is sent anywhere. More about embedding.

Questions people ask

What angle do I cut crown molding at for a 90 degree corner?

Laid flat: for 52/38 crown, a 31.62° miter and 33.86° bevel; for 45/45 crown, a 35.26° miter and 30° bevel.

How much crown molding do I need for a 12 × 12 room?

48 linear feet, or 52.8 ft with 10% extra: 5 pieces of 12 ft or 4 pieces of 16 ft.

What is the spring angle of crown molding?

The angle between the back of the crown and the wall when it's installed. Most is 38° (sold as 52/38) or 45° (45/45).

Can I cut crown molding without a compound saw?

Yes, by cutting it upside down and nested against the fence at a simple 45° miter, as long as you hold it at its spring angle.

How do I cut crown for a corner that isn't 90 degrees?

Measure the corner and enter it; the calculator works out the miter and bevel for that angle.

Related calculators