Calcist

Style

Buttons

Spacing

How much to show

Decimal places

Text size

Baseboard calculator

Enter your wall lengths and doors to get the linear feet of baseboard, with 10% extra, and the pieces to buy in 8, 12 or 16 ft lengths.

Private: calculated on your device. Nothing you type is sent anywhere.

Next: Doing the ceiling trim too? The crown molding calculator adds the saw angles.

How baseboard is measured

Linear feet = sum of the wall lengths − openings
With waste = linear feet × (1 + waste % ÷ 100)
Pieces = linear feet with waste ÷ piece length, rounded up
Pieces if every wall is cut from its own stock = Σ (wall length ÷ piece length, rounded up)

Metrie, a moulding maker, suggests buying about 10% extra for bad cuts and damage. The calculator gives two piece counts: by total footage, and wall by wall (each wall cut from its own pieces, so there are no joints on walls up to the piece length).

Worked example

A 12 × 14 ft room has walls of 12, 14, 12 and 14 ft: 52 ft. Take off one 3 ft door: 49 linear feet. Add 10%: 53.9 ft. In 16 ft pieces: 53.9 ÷ 16 = 3.37, so 4 pieces by footage. Cutting each wall from its own piece needs 1 piece per wall, so also 4. In 8 ft pieces the footage count is 7, but wall by wall it's 2 + 2 + 2 + 2 = 8 (each wall over 8 ft needs a joint).

Subtracting doors

Baseboard stops at each door casing, so subtract the width of every door opening from the wall it's on. Don't subtract a closet with no door; its inside walls need baseboard too, so add them as walls of their own.

Scribing to an uneven floor

Floors are rarely flat, and a straight baseboard leaves gaps over the low spots. Scribing trims the bottom of the board to follow the floor while its top stays level. Hold the board in place with its top level (shim it if needed), set a scribing compass to the largest gap, and run it along the floor to draw the floor's shape on the board. Cut to the line and fine-tune with a block plane. A slight back-bevel on the bottom edge makes the board easier to fit. If you'll add shoe molding or quarter round, it can hide small gaps instead.

Coping inside corners

At an inside corner, run the first piece square into the wall. Cut the second piece with a 45° inside miter to reveal its profile, then cut along that profile line with a coping saw, angling the saw back a little. The coped end fits over the face of the first piece. A coped joint hides corners that aren't exactly 90° and is less likely to open up as the wood moves than a plain miter. Outside corners are still mitered.

Scarf joints on long walls

When a wall is longer than your pieces, join two pieces with a scarf joint rather than a square butt joint. Cut the ends at opposing 45° angles so they overlap, glue them, and nail through the overlap, over a stud if you can. Keep scarf joints out of the most visible spots, such as the middle of a wall facing the door. Each scarf uses a few extra inches of stock, which the 10% waste covers. The wall-by-wall count above tells you how many joints you'll need: any wall that takes more than one piece has one.

Getting a realistic number

  • Closets and short returns count as walls; measure them separately.
  • Outside corners waste more trim than coped inside corners, so add more than 10% for rooms with many of them.
  • Shoe molding or quarter round runs the same length as the baseboard, if you're adding it.

Sources

How we checked this

Before every update, this calculator is run in a real browser with these known answers, and it must match all of them:

  • Walls 12, 14, 12, 14 less one 3 ft door: 49 ft ✓
  • Same with 10%: 53.9 ft, 4 pieces of 16 ft ✓
  • 8 ft pieces: 7 by footage, 8 wall by wall ✓
  • Feet and inches: 12 ft 6 in, 10 → 22.5 ft ✓
  • Edge: doors wider than the walls are refused ✓

Last checked October 26, 2026. Spotted something wrong? The math is done in your browser with the formula shown on this page, so you can check any result by hand.

Add this calculator to your website (free)

Paste this code into any web page. The calculator works on your page, resizes itself, has no ads and no tracking cookies, and nothing your visitors type is sent anywhere. More about embedding.

Questions people ask

How much baseboard do I need for a 12 × 12 room?

48 ft of wall, minus a 3 ft door, is 45 linear feet; with 10% extra, 49.5 ft. That's 4 pieces of 16 ft or 5 pieces of 12 ft.

How do I calculate linear feet of baseboard?

Add the lengths of all the walls, subtract the width of each door opening, then add about 10% for waste.

What lengths does baseboard come in?

Commonly 8, 12 and 16 ft; longer pieces mean fewer joints but are harder to transport.

Should I subtract doors from baseboard?

Yes, subtract the door openings. Don't subtract closets with no doors; they need baseboard inside.

How much extra baseboard should I buy?

About 10%, as Metrie suggests, and more for rooms with many outside corners or short walls.

Related calculators