Calcist

Style

Buttons

Spacing

How much to show

Decimal places

Text size

Voltage divider calculator

Work out the output voltage of a two-resistor divider, or the resistor you need for a target voltage. Add a load to see how much it drags the output down.

Private: calculated on your device. Nothing you type is sent anywhere.

Next: Need a single resistor's current or power? Use the Ohm's law calculator.

What it does

A voltage divider is two resistors in series across a supply. The voltage at the point between them is a fixed fraction of the input. It's the standard way to scale a signal down, for example to read a 12 V battery with a 5 V or 3.3 V microcontroller, or to set a reference voltage. This calculator finds the output voltage, or the value of R1 or R2 that gives the output you want. It also shows the current, the power in each resistor and the effect of a load connected across the output.

How it's calculated

Vout = Vin × R2 ÷ (R1 + R2)
R1 = R2 × (Vin − Vout) ÷ Vout  ·  R2 = R1 × Vout ÷ (Vin − Vout)
With a load RL: replace R2 with R2 ∥ RL = R2 × RL ÷ (R2 + RL)

R1 connects the input to the output point, and R2 connects the output to ground. The same current, I = Vin ÷ (R1 + R2), flows through both resistors in series, and each one drops V = I × R. Any load connected across the output sits in parallel with R2 and lowers the effective bottom resistance, so the output falls.

Worked examples

  • 5 V to about 3.3 V: SparkFun's example uses R1 = 1.8 kΩ and R2 = 3.3 kΩ. Vout = 5 × 3.3 ÷ (1.8 + 3.3) = 5 × 3.3 ÷ 5.1 = 3.235 V.
  • Choosing R2: you want 3.3 V from 5 V with R1 = 10 kΩ. R2 = 10 × 3.3 ÷ (5 − 3.3) = 33 ÷ 1.7 = 19.41 kΩ. The nearest common value, 20 kΩ, gives 5 × 20 ÷ 30 = 3.33 V.
  • The load effect: 12 V across two 10 kΩ resistors gives 6 V. Connect a 10 kΩ load across R2 and the bottom becomes 10 ∥ 10 = 5 kΩ, so Vout = 12 × 5 ÷ 15 = 4 V. The output dropped by a third.

Getting a realistic number

  • Keep the load light. A rule of thumb is to make the load at least 10 times larger than R2, so the output changes by less than about 10%.
  • Don't power things from a divider. As SparkFun points out, the current a load draws also flows through R1 and is wasted as heat. Use a voltage regulator to power circuits; use a divider to scale signals.
  • Resistor tolerance: with 5% resistors, the output can be off by a few percent. Use 1% resistors for measurements.
  • Check resistor power ratings. Small resistors are often rated 1/8 W or 1/4 W. The calculator shows the power in each.

Sources

How we checked this

Before every update, this calculator is run in a real browser with these known answers, and it must match all of them:

  • 5 V with 1.8 kΩ and 3.3 kΩ: 3.23529 V ✓
  • 12 V across two 10 kΩ: 6 V ✓
  • A 10 kΩ load pulls that to 4 V ✓
  • 5 V to 3.3 V with R1 = 10 kΩ needs R2 = 19.4118 kΩ ✓
  • 12 V to 5 V with R2 = 10 kΩ needs R1 = 14 kΩ ✓
  • An output at or above the input is refused ✓
  • A load too heavy for the target output is caught ✓

Last checked October 26, 2026. Spotted something wrong? The math is done in your browser with the formula shown on this page, so you can check any result by hand.

Add this calculator to your website (free)

Paste this code into any web page. The calculator works on your page, resizes itself, has no ads and no tracking cookies, and nothing your visitors type is sent anywhere. More about embedding.

Questions people ask

What is the voltage divider formula?

Vout = Vin × R2 ÷ (R1 + R2), where R2 is the resistor between the output and ground.

How do I choose resistors for a voltage divider?

Pick R1, then R2 = R1 × Vout ÷ (Vin − Vout). For signals, values from about 1 kΩ to 100 kΩ are common: high enough to waste little current, low enough that the input you connect doesn't load it much.

What happens if two resistors are equal?

The output is exactly half the input, for example 6 V from 12 V, as long as there's no load.

Why does my divider's output drop when I connect something?

The load is in parallel with R2, which lowers the bottom resistance. Enter the load resistance here to see the new output.

Can a voltage divider step voltage up?

No. Vout is always less than Vin, because R2 ÷ (R1 + R2) is always less than 1.

Related calculators